ard_adt7470/adt7470.ino

/*
ADT7470 address selection
FOR 7470's PIN 11:
High (10k to Vcc)   = 010 1111 (0x5E left justified or 0x2F right justified)
Low (10k to GND)    = 010 1100 (0x58 left justified or 0x2C right justified)
Float (none)        = 010 1110 (0x5C left justified or 0x2E right justified)
*/

#include <Wire.h>

#DEFINE ADT_ADDR 0x58
#DEFINE ADT_ADDR_LOW   0x5E
#DEFINE ADT_ADDR_FLOAT 0x58
#DEFINE ADT_ADDR_HIGH  0x5C
//#DEFINE PIN_I2C  10
#DEFINE PIN_FULL 11
#DEFINE START_FULL 1
#DEFINE START_FULL_DURATION 1000

//how many sensors do we have?
byte temp_numsensors = 10;
//when was the temp taken?
unsigned long temp_millis = 0;

unsigned long temp_age () {
    return millis() - temp_millis;
}
//start measurements
//wait 200ms per sensor in chain
void temp_measure(bool delay = true) {
    //set register address 0x40 Bit[7] = 1
    byte config = conf_get1();
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x40));

    if (enable) {
        bitSet(config,7);
    }
    else {
        bitClear(config,7);
    }
    Write.write(config);
    Wire.endTransmission();
    //wait for 200ms * temp_numsensors
    if (delay) {
        delay(200*temp_numsensors);
        temp_millis = millis();
    }
    else
    {
        temp_millis = millis() + 200*temp_numsensors;
    }
    //temps are ready
}
//get temp of specific
byte temp_get (byte sensor) {
    //sensor 0 at 0x20
    //sensor 9 at 0x29
    if (sensor <= 9)
    {
        Wire.beginTransmission(byte(ADT_ADDR));
        Wire.write(byte(0x20)+sensor);
        Wire.endTransmission();
        Wire.requestFrom(byte(ADT_ADDR),1);
        if (1 == Wire.available())
            return Wire.read();
    }
    return 0;
}
void temp_getmax (void) {
    //read max TMP05 temperature
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x78));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    return 0;
}

void fans_full_speed (bool stuck) {
    //pull PIN_FULL low until cleared
}

void fans_full_speed_time (int ms) {
    //pull PIN_FULL low for ms
}
int fans_rpm (byte fan) {
    //page 23+24
    //tach 0 low at  0x2A
    //tach 0 high at 0x2B
    if (fan <= 3)
    {
        Wire.beginTransmission(byte(ADT_ADDR));
        Wire.write(byte(0x2A)+(fan*2));
        Wire.endTransmission();
        Wire.requestFrom(byte(ADT_ADDR),2);
        if (2 == Wire.available())
            return ((unsigned int)Wire.read() << 8 ) + Wire.read();
    }
    return 0;
}
void fans_setpct (int fan, byte pct) {
    fans_set(fan,pct/0.39);
}
void fans_set (int fan, byte duty) {
    //page 25
    if (fan <= 3)
    {
        Wire.beginTransmission(byte(ADT_ADDR));
        Wire.write(byte(0x32) + fan);
        Wire.write(duty);
        Wire.endTransmission();
    }
}
//----configuration----
//get config register 1, 0x40
byte conf_get1 () {
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x40));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    else
        return 0;
}
//get config register 2, 0x74
byte conf_get2 () {
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x74));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    else
        return 0;
}

//page 30 + 36
void conf_monitor (bool enable) {
    //set 1 in bit0 of register 1 (0x40) to monitor all tachs and temps
    //typo? - set 0 in bit7??? of register 1 (0x40) to monitor all tachs and temps (pg7)
    byte config = conf_get1();
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x40));

    if (enable) {
        bitSet(config,0);
    }
    else {
        bitClear(config,0); //need verify cuz possible datasheet typo
    }
    Write.write(config);
    Wire.endTransmission();
}
void conf_lowspeed (){}
void conf_measure_tach (int tach, bool enable) {
    //page 36
}

//----device----
byte device_id () {
    //get 0x3d, should be 0x70
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x3d));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    else
        return 0;
}
byte device_company () {
    //get 0x3e, should be 0x41
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x3e));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    else
        return 0;
}
byte device_revision () {
    //get 0x3f
    Wire.beginTransmission(byte(ADT_ADDR));
    Wire.write(byte(0x3f));
    Wire.endTransmission();
    Wire.requestFrom(byte(ADT_ADDR),1);
    if (1 == Wire.available())
        return Wire.read();
    else
        return 0;
}
//----GPIO STUFF----
//page 8
//---------

void setup(void){
    Wire.begin(); //join i2c as master
    //if start full speed fans

}

void loop(void){


}