ProjectPatatoe
21dc393e10
swithced to MPC for PETG starting config.ini but not ready included prusaslicer config bundle
815 lines
24 KiB
INI
815 lines
24 KiB
INI
# generated by PrusaSlicer 2.9.1 on 2025-03-26 at 02:10:20 UTC
|
|
|
|
[print:d-bot_2022]
|
|
arc_fitting = disabled
|
|
automatic_extrusion_widths = 0
|
|
automatic_infill_combination = 0
|
|
automatic_infill_combination_max_layer_height = 100%
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bed_temperature_extruder = 0
|
|
bottom_fill_pattern = monotonic
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0
|
|
bridge_acceleration = 0
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 1
|
|
bridge_speed = 60
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 3
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 0
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
ensure_vertical_shell_thickness = partial
|
|
external_perimeter_acceleration = 0
|
|
external_perimeter_extrusion_width = 0.45
|
|
external_perimeter_speed = 50%
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 1
|
|
extra_perimeters_on_overhangs = 0
|
|
extrusion_width = 0.45
|
|
fill_angle = 45
|
|
fill_density = 20%
|
|
fill_pattern = adaptivecubic
|
|
first_layer_acceleration = 0
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.42
|
|
first_layer_height = 0.35
|
|
first_layer_infill_speed = 0
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 20
|
|
gcode_comments = 0
|
|
gcode_label_objects = octoprint
|
|
gcode_resolution = 0.0125
|
|
gcode_substitutions =
|
|
infill_acceleration = 0
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 50
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.45
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 80
|
|
inherits =
|
|
interface_shells = 0
|
|
interlocking_beam = 0
|
|
interlocking_beam_layer_count = 2
|
|
interlocking_beam_width = 0.8
|
|
interlocking_boundary_avoidance = 2
|
|
interlocking_depth = 2
|
|
interlocking_orientation = 22.5
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.3
|
|
max_print_speed = 80
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 0
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 0
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_one_perimeter_first_layer = 0
|
|
only_retract_when_crossing_perimeters = 0
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base].gcode
|
|
over_bridge_speed = 0
|
|
overhang_speed_0 = 15
|
|
overhang_speed_1 = 15
|
|
overhang_speed_2 = 20
|
|
overhang_speed_3 = 25
|
|
overhangs = 1
|
|
perimeter_acceleration = 0
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.45
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 60
|
|
perimeters = 3
|
|
post_process =
|
|
print_settings_id = d-bot_2022
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0
|
|
scarf_seam_entire_loop = 0
|
|
scarf_seam_length = 20
|
|
scarf_seam_max_segment_length = 1
|
|
scarf_seam_on_inner_perimeters = 0
|
|
scarf_seam_only_on_smooth = 1
|
|
scarf_seam_placement = nowhere
|
|
scarf_seam_start_height = 0%
|
|
seam_gap_distance = 15%
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 6
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 15
|
|
solid_infill_acceleration = 0
|
|
solid_infill_below_area = 70
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.45
|
|
solid_infill_speed = 40
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 0
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.2
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0.35
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 3
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0
|
|
support_material_interface_speed = 100%
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 60
|
|
support_material_style = grid
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 0
|
|
support_material_with_sheath = 1
|
|
support_material_xy_spacing = 50%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 15%
|
|
thick_bridges = 1
|
|
thin_walls = 1
|
|
top_fill_pattern = monotonic
|
|
top_infill_extrusion_width = 0.4
|
|
top_one_perimeter_type = none
|
|
top_solid_infill_acceleration = 0
|
|
top_solid_infill_speed = 15
|
|
top_solid_layers = 3
|
|
top_solid_min_thickness = 0
|
|
travel_acceleration = 0
|
|
travel_speed = 120
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_acceleration = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_flow = 100%
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_width = 60
|
|
xy_size_compensation = 0
|
|
|
|
[filament:ABS-Gray]
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 100
|
|
chamber_minimal_temperature = 0
|
|
chamber_temperature = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.95
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_abrasive = 0
|
|
filament_colour = #C0C0C0
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 0
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_infill_max_crossing_speed = 0
|
|
filament_infill_max_speed = 0
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100%
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_seam_gap_distance = nil
|
|
filament_settings_id = ""
|
|
filament_shrinkage_compensation_xy = 0%
|
|
filament_shrinkage_compensation_z = 0%
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 20
|
|
filament_toolchange_delay = 0
|
|
filament_travel_lift_before_obstacle = nil
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 110
|
|
first_layer_temperature = 240
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 5
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 230
|
|
|
|
[filament:ABS-Yellow]
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 100
|
|
chamber_minimal_temperature = 0
|
|
chamber_temperature = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_abrasive = 0
|
|
filament_colour = #FFFF00
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 0
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_infill_max_crossing_speed = 0
|
|
filament_infill_max_speed = 0
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100%
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_seam_gap_distance = nil
|
|
filament_settings_id = ""
|
|
filament_shrinkage_compensation_xy = 0%
|
|
filament_shrinkage_compensation_z = 0%
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 20
|
|
filament_toolchange_delay = 0
|
|
filament_travel_lift_before_obstacle = nil
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 110
|
|
first_layer_temperature = 240
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 5
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 230
|
|
|
|
[filament:Inland-PetG+-Gray-2025-03-19]
|
|
bed_temperature = 85
|
|
bridge_fan_speed = 100
|
|
chamber_minimal_temperature = 0
|
|
chamber_temperature = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_abrasive = 0
|
|
filament_colour = #7F7F7F
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 20
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_infill_max_crossing_speed = 0
|
|
filament_infill_max_speed = 0
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100%
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_seam_gap_distance = nil
|
|
filament_settings_id = ""
|
|
filament_shrinkage_compensation_xy = 0%
|
|
filament_shrinkage_compensation_z = 0%
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 20
|
|
filament_toolchange_delay = 0
|
|
filament_travel_lift_before_obstacle = nil
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 85
|
|
first_layer_temperature = 260
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 40
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 5
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 260
|
|
|
|
[filament:d-bot_2022]
|
|
bed_temperature = 110
|
|
bridge_fan_speed = 100
|
|
chamber_minimal_temperature = 0
|
|
chamber_temperature = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_abrasive = 0
|
|
filament_colour = #29B2B2
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 0
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_infill_max_crossing_speed = 0
|
|
filament_infill_max_speed = 0
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100%
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_seam_gap_distance = nil
|
|
filament_settings_id = ""
|
|
filament_shrinkage_compensation_xy = 0%
|
|
filament_shrinkage_compensation_z = 0%
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 20
|
|
filament_toolchange_delay = 0
|
|
filament_travel_lift_before_obstacle = nil
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 110
|
|
first_layer_temperature = 230
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 5
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 230
|
|
|
|
[printer:d-bot_2022]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,215x0,215x125,0x125
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
binary_gcode = 0
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile =
|
|
default_print_profile =
|
|
deretract_speed = 0
|
|
end_gcode = ;custom end gcode\nM104 S0 ; turn off temperature\nM140 S0 ; turn off bed\nG1 X0 Y220 ; home X axis / present print\n;M84 ; disable motors\nM300 S1000 P1000 ;BEEP\nG4 S1 ;wait\nM300 S1500 P1000 ;BEEP\n;end custom end gcode
|
|
extra_loading_move = -2
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_colour = ""
|
|
extruder_offset = 0x0
|
|
gcode_flavor = marlin2
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 10000,5000
|
|
machine_max_acceleration_extruding = 1500,1250
|
|
machine_max_acceleration_retracting = 1500,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 9000,1000
|
|
machine_max_acceleration_y = 9000,1000
|
|
machine_max_acceleration_z = 500,200
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 500,200
|
|
machine_max_feedrate_y = 500,200
|
|
machine_max_feedrate_z = 12,12
|
|
machine_max_jerk_e = 2.5,2.5
|
|
machine_max_jerk_x = 10,10
|
|
machine_max_jerk_y = 10,10
|
|
machine_max_jerk_z = 0.2,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 200
|
|
min_layer_height = 0.07
|
|
multimaterial_purging = 140
|
|
nozzle_diameter = 0.4
|
|
nozzle_high_flow = 0
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = M601
|
|
prefer_clockwise_movements = 0
|
|
print_host =
|
|
printer_model =
|
|
printer_notes =
|
|
printer_settings_id =
|
|
printer_technology = FFF
|
|
printer_variant =
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 0
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 0
|
|
retract_length = 2
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0
|
|
retract_lift_below = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 1
|
|
single_extruder_multi_material = 0
|
|
start_gcode = ;custom printer settings\nG28 ; home all axes\nG29 ; probe bed\n\nM420 S1 ; turn bed leveling on again\n\nM420 Z1 ; Fade height set to 1mm\nG1 Z15 F1000 ; lift nozzle\nG1 X0 Y50 F10000 ; wait on the side for heat/ooze\n;end custom printer settings
|
|
template_custom_gcode =
|
|
thumbnails =
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
travel_lift_before_obstacle = 0
|
|
travel_max_lift = 0
|
|
travel_ramping_lift = 0
|
|
travel_slope = 0
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[printer:d-bot_2022_dec]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,215x0,215x125,0x125
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
binary_gcode = 0
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile =
|
|
default_print_profile =
|
|
deretract_speed = 0
|
|
end_gcode = ;custom end gcode\nM104 S0 ; turn off temperature\nM140 S0 ; turn off bed\nG1 X0 Y220 ; home X axis / present print\n;M84 ; disable motors\nM300 S1000 P1000 ;BEEP\nG4 S1 ;wait\nM300 S1500 P1000 ;BEEP\n;end custom end gcode
|
|
extra_loading_move = -2
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_colour = ""
|
|
extruder_offset = 0x0
|
|
gcode_flavor = marlin2
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 10000,5000
|
|
machine_max_acceleration_extruding = 1500,1250
|
|
machine_max_acceleration_retracting = 1500,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1500,1000
|
|
machine_max_acceleration_y = 1500,1000
|
|
machine_max_acceleration_z = 100,100
|
|
machine_max_feedrate_e = 10,10
|
|
machine_max_feedrate_x = 200,200
|
|
machine_max_feedrate_y = 200,200
|
|
machine_max_feedrate_z = 20,12
|
|
machine_max_jerk_e = 2.5,2.5
|
|
machine_max_jerk_x = 7,7
|
|
machine_max_jerk_y = 7,7
|
|
machine_max_jerk_z = 0.2,0.2
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 275
|
|
min_layer_height = 0.07
|
|
multimaterial_purging = 140
|
|
nozzle_diameter = 0.4
|
|
nozzle_high_flow = 0
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = M601
|
|
prefer_clockwise_movements = 0
|
|
print_host =
|
|
printer_model =
|
|
printer_notes =
|
|
printer_settings_id =
|
|
printer_technology = FFF
|
|
printer_variant =
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 0
|
|
retract_length = 2
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0
|
|
retract_lift_below = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 1
|
|
single_extruder_multi_material = 0
|
|
start_gcode = ;custom printer settings\nG28 ; home all axes\nG29 ; probe bed\n\nM420 S1 ; turn bed leveling on again\n\nM420 Z1 ; Fade height set to 1mm\nG1 Z15 F1000 ; lift nozzle\nG1 X0 Y50 F10000 ; wait on the side for heat/ooze\n;end custom printer settings
|
|
template_custom_gcode =
|
|
thumbnails =
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
travel_lift_before_obstacle = 0
|
|
travel_max_lift = 0
|
|
travel_ramping_lift = 0
|
|
travel_slope = 0
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[printer:d-bot_2025-03-19]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,215x0,215x125,0x125
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
binary_gcode = 0
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile =
|
|
default_print_profile =
|
|
deretract_speed = 0
|
|
end_gcode = ;custom end gcode\nM104 S0 ; turn off temperature\nM140 S0 ; turn off bed\nG1 X0 Y220 ; home X axis / present print\n;M84 ; disable motors\nM300 S1000 P1000 ;BEEP\nG4 S1 ;wait\nM300 S1500 P1000 ;BEEP\n;end custom end gcode
|
|
extra_loading_move = -2
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_colour = ""
|
|
extruder_offset = 0x0
|
|
gcode_flavor = marlin2
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 10000,5000
|
|
machine_max_acceleration_extruding = 1500,1250
|
|
machine_max_acceleration_retracting = 1500,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1500,1000
|
|
machine_max_acceleration_y = 1500,1000
|
|
machine_max_acceleration_z = 100,100
|
|
machine_max_feedrate_e = 10,10
|
|
machine_max_feedrate_x = 200,200
|
|
machine_max_feedrate_y = 200,200
|
|
machine_max_feedrate_z = 20,12
|
|
machine_max_jerk_e = 2.5,2.5
|
|
machine_max_jerk_x = 7,7
|
|
machine_max_jerk_y = 7,7
|
|
machine_max_jerk_z = 0.2,0.2
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 275
|
|
min_layer_height = 0.07
|
|
multimaterial_purging = 140
|
|
nozzle_diameter = 0.6
|
|
nozzle_high_flow = 0
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = M601
|
|
prefer_clockwise_movements = 0
|
|
print_host =
|
|
printer_model =
|
|
printer_notes =
|
|
printer_settings_id =
|
|
printer_technology = FFF
|
|
printer_variant =
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 0
|
|
retract_length = 2
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0
|
|
retract_lift_below = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 1
|
|
single_extruder_multi_material = 0
|
|
start_gcode = ;custom printer settings\nG28 ; home all axes\nG29 ; probe bed\n\nM420 S1 ; turn bed leveling on again\n\nM420 Z1 ; Fade height set to 1mm\nG1 Z15 F1000 ; lift nozzle\nG1 X0 Y50 F10000 ; wait on the side for heat/ooze\n;end custom printer settings
|
|
template_custom_gcode =
|
|
thumbnails =
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
travel_lift_before_obstacle = 0
|
|
travel_max_lift = 0
|
|
travel_ramping_lift = 0
|
|
travel_slope = 0
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[presets]
|
|
print = d-bot_2022
|
|
sla_print =
|
|
sla_material =
|
|
printer = d-bot_2025-03-19
|
|
filament = Inland-PetG+-Gray-2025-03-19
|
|
physical_printer =
|